I have been having problems with the server running out of resources and giving errors. It is better but I'm still getting some periodically. Please report any you get to me at ken@kyler.com.
What did you work on today?
- gots_a_sol
- DAMN Grand Poohba
- Posts: 1014
- Joined: Sat Jul 26, 2014 7:08 am
- Contact:
Re: What did you work on today?
Stuck the sand/mud tires on the beta for the national enduro this weekend.
Dunlop mx11. I have a Bridgestone m101 on the front. I've owned both of these over a year and this is the first time using the rear and the front has only seen one race
Dunlop mx11. I have a Bridgestone m101 on the front. I've owned both of these over a year and this is the first time using the rear and the front has only seen one race
Last edited by gots_a_sol on Fri Jan 31, 2020 11:12 pm, edited 3 times in total.
-Joe.
'22 YZ250FX
'09 Husky WR177
'22 YZ250FX
'09 Husky WR177
- juddspaintballs
- DAMN Grand Poohba
- Posts: 1755
- Joined: Wed Nov 14, 2012 8:32 am
- Contact:
Re: What did you work on today?
Which tire is that? Looks a lot like the Geomax Sand/Mud.
Jed Gregory
1090 Adventure R
1090 Adventure R
Re: What did you work on today?
Good luck! Post a report when you get back.gots_a_sol wrote: ↑Fri Jan 31, 2020 11:07 pmStuck the sand/mud tires on the beta for the national enduro this weekend.
- gots_a_sol
- DAMN Grand Poohba
- Posts: 1014
- Joined: Sat Jul 26, 2014 7:08 am
- Contact:
Re: What did you work on today?
Got the firewall pieced back together and I am much happier with it now than it was with the ford v8. Other than a bump out on the drivers side for the intake manifold, the firewall/floor with be mostly stock again.
At some point in the last 65 years someone else had hacked out a hole in the firewall. I do not own a bead roller so this piece took quite a while to make by hand.
Sumter didn't go well btw. Nagging issue with the Beta is still there so I basically tried to enjoyed my trail ride all day. The tires hooked up great though
At some point in the last 65 years someone else had hacked out a hole in the firewall. I do not own a bead roller so this piece took quite a while to make by hand.
Sumter didn't go well btw. Nagging issue with the Beta is still there so I basically tried to enjoyed my trail ride all day. The tires hooked up great though
-Joe.
'22 YZ250FX
'09 Husky WR177
'22 YZ250FX
'09 Husky WR177
Re: What did you work on today?
Changed the gear oil on the trials bike. Had a heck of a time getting the oil in the tiny hole. Finally used a big syringe. Worked great!
Yamaha WR250R
Yamaha TW200
Yamaha TW200
Re: What did you work on today?
Poured electrons into the EM's fuel tank.
Ken
Die young as late as possible, remember who you were before the world told you how it should be. -- Barry Morris
Die young as late as possible, remember who you were before the world told you how it should be. -- Barry Morris
Re: What did you work on today?
Yamaha WR250R
Yamaha TW200
Yamaha TW200
Re: What did you work on today?
I made the first of four under body storage boxes and I made a seat frame and springs for the 36 Chevy. I changed the rear calipers and brake pads on the F250, had a stuck caliper and hot brake. I also got about 30 min of riding time on the EM in the backyard.
- Firebolter
- DAMN Grand Poohba
- Posts: 2468
- Joined: Wed Mar 03, 2010 9:19 am
- Contact:
Re: What did you work on today?
I drilled and tapped the caliper carrier to accept the second wheel sensor for the Voyager pro. I like to be able to run my stock ODO and the Voyager so I have both. The "Brembo" logo on the caliper carrier is in the perfect spot, just punched it right in the center of the logo, drilled a small pilot hole, then drilled a 17/64 hole and tapped with with the M8-1.25 for the Trailtech sensor to thread in. perfect fit! Then I worked on my van "flow wall" set up so I can start hanging up my stuff. Just waiting on the liners to show up so I can finish out the inside of the van. Nice day to work on projects for sure.
Lots of cool bikes---
Who is online
Users browsing this forum: Google [Bot] and 25 guests